WASHER

OPTION CLAUSE: The Purchaser reserves the right to increase or decrease the quantity to be ordered up to 25 percent of bid quantity at the time of placement of contract. The purchaser also reserves the right to increase the ordered quantity up to 25% of the contracted quantity during the currency of the contract at the contracted rates. The delivery period of quantity shall commence from the last date of original delivery order and in cases where option clause is exercised during the extended delivery period the additional time shall commence from the last date of extended delivery period. The additional delivery time shall be (Increased quantity ÷ Original quantity) × Original delivery period (in days), subject to minimum of 30 days. If the original delivery period is less than 30 days, the additional time equals the original delivery period. The Purchaser may extend this calculated delivery duration up to the original delivery period while exercising the option clause. Bidders must comply with these terms.

Bidder financial standing: The bidder should not be under liquidation, court receivership or similar proceedings, should not be bankrupt. Bidder to upload undertaking to this effect with bid.

Bidders are advised to check applicable GST on their own before quoting. Buyer will not take any responsibility in this regards. GST reimbursement will be as per actuals or as per applicable rates (whichever is lower), subject to the maximum of quoted GST %.

Bidder's offer is liable to be rejected if they don't upload any of the certificates / documents sought in the Bid document, ATC and Corrigendum if any.

Buyer Added text based ATC clauses Enquiry For Material :- Sl N o Material Description Material Co de Quanti ty Unit 1 WASHER (HW-250.59) -- FULLY M/CD ITEM AS PER DRG. 41240409017 R EV.00 WITH MATL. HW10683 REV.03 RV10194310 09

NOS 2 SPINDLE VAR.01 (HW-065.01.08) -- FULLY M/CD ITEM AS PER DRG. 4120 2524008 REV.01 WITH MATL. HW10683 REV.03 RV10194336 18

NOS 3 SPINDLE VAR.00 (HW-065.02.06) -- FULLY M/CD ITEM AS PER DRG. 4120 2524008 REV.01 WITH MATL. HW10683 REV.03 RV10194336 19

NOS 4 STUD M42 (HW-292.10)- FULLY M/CD ITEM AS PER DRG.41202657001 RE V.00 WITH MATL. AS HW10683 REV.03 RV95300013 98

NOS 5 NUT HEX PM56 (HW-114.86) -- FULLY M/CD ITEM AS PER STD. ST03003 R EV.02 (SIZE NO. 056) WITH MATL. HW10673 REV.03 RV95373305 67

NOS Remarks (A) SUPPLY CONDITION

TIVE AS PER QP RV/MCD/39 REV.06. FOR REVISION OF DRAWING/STANDARD/SPECIFICATION, PLE ASE REFER THE ATTACHED DOCUMENT NO. " IND202610892 ", DURING INSPECTION. (B) TECHNICAL DELIVERY CONDITION:

MPLETELY FREE FROM CHATTERING MARKS.

THE APPROVED SOURCES FOR RAW MATL. HW10683 (PMD ST09/03) ARE: Sl VendorName CITY 1 M/S BGH EDELSTAHL FREITAL GMBH FREITAL 2 M/s BHEL HEEP HARIDWAR HARIDWAR 3 M/S BOHLER INTERNATIONAL GMBH VIENNA 4 M/S LAXCON STEELS LIMITED AHMEDABAD 5 M/S MAHINDRA SANYO SPECIAL STEEL PRIVATE LIMITED RAIGAD 6 M/S MISHRA DHATU NIGAM LIMITED HYDERABAD 7 M/S STAR WIRE (INDIA) LIMITED BALLABGARH 8 M/S STEEL AUTHORITY OF INDIA LIMITED NEW DELHI THE APPROVED SOURCES FOR RAW MATL. HW10673 (PMD ST09/15) ARE: 1 M/S BGH EDELSTAHL FREITAL GMBH FREITAL 2 M/S BOHLER INTERNATIONAL GMBH VIENNA 3 M/S KALYANI CARPENTER SPECIAL STEEL LTD PUNE 4 M/S KISCO CASTINGS (INDIA) LTD MANDI GOBINDGARH 5 M/S LAXCON STEELS LIMITED AHMEDABAD 6 M/S MAHINDRA SANYO SPECIAL STEEL PRIVATE LIMITED RAIGAD 7 M/S MISHRA DHATU NIGAM LIMITED HYDERABAD 8 M/S STAR WIRE (INDIA) LIMITED BALLABGARH 9 M/S STEEL AUTHORITY OF INDIA LIMITED NEW DELHI IF VENDOR IS UNABLE TO PROCURE RAW MATL. FROM APPROVED SOURCE DUE TO SMALL QTY, T HEY MAY PROCURE IT FROM TRADER AND FURNISH NABL TC.

MILL TC OF RAW MATL. SUPPLIER.

DETAIL FOR LINKING THE ITEM WITH RAW MATL. SOURCE TO BE MAINTAINED BY VENDOR.

HEL APPROVED SOURCE AS PER SPECN. 0912.002 MENTIONED IN THE DRG. BHEL APPROVED SOURCES FOR NITRIDING (PMD-STSC-016) ARE; 1 M/s HEAT TREAT ENTERPRISE AHMEDABAD 2 M/s MODERN METALS INDIA PRIVATE LIMITED FARIDABAD 3 M/s SHIVA TECHNIQUES SURFACES PRIVATE LIMITED FARIDABAD

G.) SHALL NOT BE DONE BY THE PARTY. (C)TEST CERTIFICATE :REQUIRED FOR CHEMICAL AND MECHANICAL PROPERTIES (MILL TC IS REQ UIRED). FURTHER REQUIRED FOR NDT OF MATL. REQUIRED FOR HARDNESSS AND CASE DEPTH A FTER NITRIDING (IF MENTIONED IN THE DRG). (D) GUARANTEE/WARRANTY CERTIFICATE :REQUIRED FOR 24 MONTHS AGAINST ANY MANUFACT URING DEFECTS. (E)PACKING INSTRUCTION: ITEM TO BE SUPPLIED IN PROPERLY PACKED CONDITION IN WOODEN BOX OF 1" THICK PLANK WITH 1.5"X4" BKTS. M/CD SURFACE AND THREADS SHOULD BE PROTECT ED PROPERLY WITH IOCL-SERVO RP-330 OR EQUIVALENT OIL TO PREVENT ANY RUSTING DURING TRANSIT AND STORING. ITEM SHOULD BE COMPLETELY WRAPPED IN POLYTHENE PAPER TO PREV ENT ANY TRANSIT DAMAGE. ITEM SHOULD BE PROPERLY IDENTIFIED BY PUNCHING THE DRG. NO. ON EACH ITEM. NITRIDED SURFACE OF THESE TYPE OF ITEMS SHOULD BE COVERED WITH BUBBL E SHEET, FOAM SHEET ETC. TO PROTECT IT FROM DAMAGE DURING TRANSPORTATION. THESE ITE MS SHOULD NOT BE CLUBBED WITH OTHER LOOSE ITEMS. THESE ITEMS SHOULD BE PACKED TIG HTLY IN THE BOX. EXCESSIVE RELATIVE MOTION MAY CAUSE DAMAGE OF PROTECTION LAYERS A ND SUBSEQUENT DAMAGE OF ITEMS. (F) DELIVERY PERIOD IS 5 MONTHS FROM THE DATE OF PO. HOWEVER EARLY DELIVERY IS ACCEP TABLE. (G) ALL OTHER TERMS AND CONDITIONS SHALL BE AS PER THE ATTACHED ATC (PARTY HAS TO S TRICTLY ADHERE THESE ADDITIONAL TERMS & CONDITIONS). List of required Quality Documents along with supply:- S. N o Materi al Code Material Description Documents De scription 1 RV101943 1009 WASHER (HW-250.59) -- FULLY M/CD ITEM AS PER DRG. 4-12404-09 017 REV.00 WITH MATL. HW10683 REV.02

tes

art

y TPI/BHEL

emical Properties

chanical Properties 2 RV101943 3618 SPINDLE VAR.01 (HW-065.01.08) -- FULLY M/CD ITEM AS PER DRG. 41202524008 REV.01 WITH MATL. HW10683 REV.03

emical Properties

chanical Properties

art

y TPI/BHEL

tes 3 RV101943 3619 SPINDLE VAR.00 (HW-065.02.06) -- FULLY M/CD ITEM AS PER DRG. 41202524008 REV.01 WITH MATL. HW10683 REV.03

art

tes

y TPI/BHEL

emical Properties

chanical Properties 4 RV953000 1398 STUD M42 (HW-292.10)- FULLY M/CD ITEM AS PER DRG.412026570 01 REV.00 WITH MATL. AS HW10683 REV.03

emical Properties

chanical Properties

y TPI/BHEL

art

tes 5 RV953733 0567 NUT HEX PM56 (HW-114.86) -- FULLY M/CD ITEM AS PER STD. ST03 003 REV.02 (SIZE NO. 056) WITH MATL. HW10673 REV.03

tes

art

y TPI/BHEL

emical Properties

chanical Properties

Note : Any other document mentioned in QP/Drg/Spec will also be applicable .

Buyer uploaded ATC document Click here to view the file . अ'वीकरण अ'वीकरण /Disclaimer